German_Force » Breno Giacomini Jersey

Tenderall Fan Co. developes Make-Up Air Unitss for larger industrial plants ventilation requirements.

Negative Air Pressure in industrial manufacturing facilities can create problems such as:

* Exhaust fans losing performance Kai Forbath Vikings Jersey , as the building pressure becomes negative.

* Pilot light outages and exhaust system failure on natural draft gas equipment.

* Cold air drafts and infiltration of dirt and contamination from outside.

* Difficulty opening or closing exterior doors.

Tenderall Co. air-handling units (AHU) can be used effectively for negative pressure control at manufacturing facilities:

Space Pressure Control is used to minimize and control the exchange of air between the building and the outside environment or from one building area to another. This may be accomplished in three ways:

- Constant air supply with variable-speed exhaust;

- Variable air supply with constant-speed exhaust;

- Variable Return-Air.

Constant air supply with variable-speed exhaust is recommended where a hot or contaminated environment must be ventilated while maintaining room pressure. Unit may be interlocked to that it only operates with the exhaust system.

Variable Air Supply with constant-speed exhaust may be preferred where fume exhausters or fume hoods are used to provide critical ventilation of contaminants from a “clean” environment while make-up air is used to maintain a positive pressure to prevent infiltration.

In either case, when the system is enabled, a pressure sensor in the building space monitors room pressure. When a high or low pressure reading is detected Nick Easton Vikings Jersey , the air supply or exhaust is adjusted to compensate.

When controlling a Variable Air Supply unit (or VAV Unit - Variable Air Volume), two methods are available:

- Damper Control - Unit discharge damper is adjusted using the damper motor.

- VFD (Variable Frequency Drive) – Controller adjusts the speed of the blower motor Discharge Damper adjustment is an older method of controlling discharge air volume. Its main advantage is that it only requires positional control of a small discharge damper motor. The major disadvantage is the wasted Horsepower of the blower motor at lower delivery rates.

In recent years, fan speed control using VFDs has become economical. In this application Ryan Quigley Vikings Jersey , a standard energy efficient motor is usually adequate down to 75% of normal motor speeds. For a fan speed down to 25%, a premium efficiency motor is required. Inverter duty motors are not usually necessary since at 25% of normal fan speed, air delivery is minimal.

Variable Frequency Drives are also programmable. They are used to provide soft starts and to ramp motor speed up or down in response to signals from the control system.

Finally Mike Remmers Vikings Jersey , in a generally “clean” environment without a critical need to remove large quantities of contaminants, a simple solution to building pressurization is a Return Air Unit with the return air damper motor controlled by building a pressure sensor. When building pressure increases, more inside air is returned through the unit Riley Reiff Vikings Jersey , relieving the pressure. When building pressure falls, more outside air is supplied to the building in order to “pump up the pressure”. Precise control of building pressure by a single piece of equipment can thus be achieved.

Additional information can be found at the Tenderall company web site http:tenderallahuindex.

Oleg Chetchel
Industrial and Commercial Air Systems Engineer
Tenderall Fan Co.
http:www.tenderallfanblowerindex
http:tenderallairhandlerindex Transportation of freight has been the most difficult task since the time of industrial revolution. Business logistics system has transformed and evolved a lot since the onset of modern industrial era. This evolution was actually possible because of the induction of technology in this system. Out of the many technological changes adopted by the logistics system, the modern trucking software technology has turn out to be the most effective instrument of transformation. Trucking software has brought out a significant improvement in the functioning of the overall transportation system. With the help of this advanced software technology Latavius Murray Vikings Jersey , the trucking industry has been providing a substantial contribution in the development and evolution of the business logistics system.

Trucking software has significantly contributed in the improvement of the functioning of freight transportation system. This software is designed in a highly organized manner, in-order to enable the trucking companies to efficiently manage their business operations. Trucking software contains various essential features to manage almost all the important processes involved in handling the trucking business. There are specially designed features to maintain invoice, pay reports and accounts related to the trucking business. Moreover Case Keenum Vikings Jersey , all the trading and documentation records can also be maintained through this software. This newly found efficiency in the trucking business is not only enhancing the revenues of the various trucking companies, but has also led to an overall growth and development of the entire transportation system.

Trucking companies are considered as significant units of the business logistics system of any nation. Therefore, improvement in the functioning of the trucking companies causes a direct and positive impact on the entire system of logistics. This indeed leads to the economic growth of a nation. Thus Danielle Hunter Vikings Jersey , trucking software technology plays a major role at the macro-economic level in any particular country. Trucking companies maintain a link between the production and consumption of goods within .